Jurris.COM
Article 4. “unsafe Handgun” And Related Definitions of California Penal Code >> Division 10. >> Title 4. >> Part 6. >> Chapter 4. >> Article 4.
As used in this part, the "drop safety requirement for
handguns" means that at the conclusion of the firing requirements for
handguns described in Section 31905, the same certified independent
testing laboratory shall subject the same three handguns of the make
and model for which certification is sought, to the following test:
(a) A primed case (no powder or projectile) shall be inserted into the chamber. For a pistol, the slide shall be released, allowing it to move forward under the impetus of the recoil spring, and an empty magazine shall be inserted. For both a pistol and a revolver, the weapon shall be placed in a drop fixture capable of dropping the pistol from a drop height of 1m + 1cm (39.4 + 0.4 in.) onto the largest side of a slab of solid concrete having minimum dimensions of 7.5 x 15 x 15 cm (3 x 6 x 6 in.). The drop distance shall be measured from the lowermost portion of the weapon to the top surface of the slab. The weapon shall be dropped from a fixture and not from the hand. The weapon shall be dropped in the condition that it would be in if it were dropped from a hand (cocked with no manual safety applied). If the pistol is designed so that upon leaving the hand a "safety" is automatically applied by the pistol, this feature shall not be defeated. An approved drop fixture is a short piece of string with the weapon attached at one end and the other end held in an air vise until the drop is initiated.
(b) The following six drops shall be performed:
(1) Normal firing position with barrel horizontal.
(2) Upside down with barrel horizontal.
(3) On grip with barrel vertical.
(4) On muzzle with barrel vertical.
(5) On either side with barrel horizontal.
(6) If there is an exposed hammer or striker, on the rearmost point of that device, otherwise on the rearmost point of the weapon.
(c) The primer shall be examined for indentations after each drop. If indentations are present, a fresh primed case shall be used for the next drop.
(d) The handgun shall pass this test if each of the three test guns does not fire the primer.
(a) A primed case (no powder or projectile) shall be inserted into the chamber. For a pistol, the slide shall be released, allowing it to move forward under the impetus of the recoil spring, and an empty magazine shall be inserted. For both a pistol and a revolver, the weapon shall be placed in a drop fixture capable of dropping the pistol from a drop height of 1m + 1cm (39.4 + 0.4 in.) onto the largest side of a slab of solid concrete having minimum dimensions of 7.5 x 15 x 15 cm (3 x 6 x 6 in.). The drop distance shall be measured from the lowermost portion of the weapon to the top surface of the slab. The weapon shall be dropped from a fixture and not from the hand. The weapon shall be dropped in the condition that it would be in if it were dropped from a hand (cocked with no manual safety applied). If the pistol is designed so that upon leaving the hand a "safety" is automatically applied by the pistol, this feature shall not be defeated. An approved drop fixture is a short piece of string with the weapon attached at one end and the other end held in an air vise until the drop is initiated.
(b) The following six drops shall be performed:
(1) Normal firing position with barrel horizontal.
(2) Upside down with barrel horizontal.
(3) On grip with barrel vertical.
(4) On muzzle with barrel vertical.
(5) On either side with barrel horizontal.
(6) If there is an exposed hammer or striker, on the rearmost point of that device, otherwise on the rearmost point of the weapon.
(c) The primer shall be examined for indentations after each drop. If indentations are present, a fresh primed case shall be used for the next drop.
(d) The handgun shall pass this test if each of the three test guns does not fire the primer.
(a) As used in this part, "firing requirement for handguns"
means a test in which the manufacturer provides three handguns of the
make and model for which certification is sought to an independent
testing laboratory certified by the Attorney General pursuant to
Section 32010. These handguns may not be refined or modified in any
way from those that would be made available for retail sale if
certification is granted. The magazines of a tested pistol shall be
identical to those that would be provided with the pistol to a retail
customer.
(b) The test shall be conducted as follows:
(1) The laboratory shall fire 600 rounds from each gun, stopping after each series of 50 rounds has been fired for 5 to 10 minutes to allow the weapon to cool, stopping after each series of 100 rounds has been fired to tighten any loose screws and clean the gun in accordance with the manufacturer's instructions, and stopping as needed to refill the empty magazine or cylinder to capacity before continuing.
(2) The ammunition used shall be of the type recommended by the handgun manufacturer in the user manual, or if none is recommended, any standard ammunition of the correct caliber in new condition that is commercially available.
(c) A handgun shall pass this test if each of the three test guns meets both of the following:
(1) Fires the first 20 rounds without a malfunction that is not due to ammunition that fails to detonate.
(2) Fires the full 600 rounds with no more than six malfunctions that are not due to ammunition that fails to detonate and without any crack or breakage of an operating part of the handgun that increases the risk of injury to the user.
(d) If a pistol or revolver fails the requirements of either paragraph (1) or (2) of subdivision (c) due to ammunition that fails to detonate, the pistol or revolver shall be retested from the beginning of the "firing requirement for handguns" test. A new model of the pistol or revolver that failed due to ammunition that fails to detonate may be submitted for the test to replace the pistol or revolver that failed.
(e) As used in this section, "malfunction" means a failure to properly feed, fire, or eject a round, or failure of a pistol to accept or eject the magazine, or failure of a pistol's slide to remain open after the magazine has been expended.
(b) The test shall be conducted as follows:
(1) The laboratory shall fire 600 rounds from each gun, stopping after each series of 50 rounds has been fired for 5 to 10 minutes to allow the weapon to cool, stopping after each series of 100 rounds has been fired to tighten any loose screws and clean the gun in accordance with the manufacturer's instructions, and stopping as needed to refill the empty magazine or cylinder to capacity before continuing.
(2) The ammunition used shall be of the type recommended by the handgun manufacturer in the user manual, or if none is recommended, any standard ammunition of the correct caliber in new condition that is commercially available.
(c) A handgun shall pass this test if each of the three test guns meets both of the following:
(1) Fires the first 20 rounds without a malfunction that is not due to ammunition that fails to detonate.
(2) Fires the full 600 rounds with no more than six malfunctions that are not due to ammunition that fails to detonate and without any crack or breakage of an operating part of the handgun that increases the risk of injury to the user.
(d) If a pistol or revolver fails the requirements of either paragraph (1) or (2) of subdivision (c) due to ammunition that fails to detonate, the pistol or revolver shall be retested from the beginning of the "firing requirement for handguns" test. A new model of the pistol or revolver that failed due to ammunition that fails to detonate may be submitted for the test to replace the pistol or revolver that failed.
(e) As used in this section, "malfunction" means a failure to properly feed, fire, or eject a round, or failure of a pistol to accept or eject the magazine, or failure of a pistol's slide to remain open after the magazine has been expended.
As used in this part, "unsafe handgun" means any pistol,
revolver, or other firearm capable of being concealed upon the
person, for which any of the following is true:
(a) For a revolver:
(1) It does not have a safety device that, either automatically in the case of a double-action firing mechanism, or by manual operation in the case of a single-action firing mechanism, causes the hammer to retract to a point where the firing pin does not rest upon the primer of the cartridge.
(2) It does not meet the firing requirement for handguns.
(3) It does not meet the drop safety requirement for handguns.
(b) For a pistol:
(1) It does not have a positive manually operated safety device, as determined by standards relating to imported guns promulgated by the federal Bureau of Alcohol, Tobacco, Firearms and Explosives.
(2) It does not meet the firing requirement for handguns.
(3) It does not meet the drop safety requirement for handguns.
(4) Commencing January 1, 2006, for a center fire semiautomatic pistol that is not already listed on the roster pursuant to Section 32015, it does not have either a chamber load indicator, or a magazine disconnect mechanism.
(5) Commencing January 1, 2007, for all center fire semiautomatic pistols that are not already listed on the roster pursuant to Section 32015, it does not have both a chamber load indicator and if it has a detachable magazine, a magazine disconnect mechanism.
(6) Commencing January 1, 2006, for all rimfire semiautomatic pistols that are not already listed on the roster pursuant to Section 32015, it does not have a magazine disconnect mechanism, if it has a detachable magazine.
(7) (A) Commencing January 1, 2010, for all semiautomatic pistols that are not already listed on the roster pursuant to Section 32015, it is not designed and equipped with a microscopic array of characters that identify the make, model, and serial number of the pistol, etched or otherwise imprinted in two or more places on the interior surface or internal working parts of the pistol, and that are transferred by imprinting on each cartridge case when the firearm is fired, provided that the Department of Justice certifies that the technology used to create the imprint is available to more than one manufacturer unencumbered by any patent restrictions.
(B) The Attorney General may also approve a method of equal or greater reliability and effectiveness in identifying the specific serial number of a firearm from spent cartridge casings discharged by that firearm than that which is set forth in this paragraph, to be thereafter required as otherwise set forth by this paragraph where the Attorney General certifies that this new method is also unencumbered by any patent restrictions. Approval by the Attorney General shall include notice of that fact via regulations adopted by the Attorney General for purposes of implementing that method for purposes of this paragraph.
(C) The microscopic array of characters required by this section shall not be considered the name of the maker, model, manufacturer's number, or other mark of identification, including any distinguishing number or mark assigned by the Department of Justice, within the meaning of Sections 23900 and 23920.
(a) For a revolver:
(1) It does not have a safety device that, either automatically in the case of a double-action firing mechanism, or by manual operation in the case of a single-action firing mechanism, causes the hammer to retract to a point where the firing pin does not rest upon the primer of the cartridge.
(2) It does not meet the firing requirement for handguns.
(3) It does not meet the drop safety requirement for handguns.
(b) For a pistol:
(1) It does not have a positive manually operated safety device, as determined by standards relating to imported guns promulgated by the federal Bureau of Alcohol, Tobacco, Firearms and Explosives.
(2) It does not meet the firing requirement for handguns.
(3) It does not meet the drop safety requirement for handguns.
(4) Commencing January 1, 2006, for a center fire semiautomatic pistol that is not already listed on the roster pursuant to Section 32015, it does not have either a chamber load indicator, or a magazine disconnect mechanism.
(5) Commencing January 1, 2007, for all center fire semiautomatic pistols that are not already listed on the roster pursuant to Section 32015, it does not have both a chamber load indicator and if it has a detachable magazine, a magazine disconnect mechanism.
(6) Commencing January 1, 2006, for all rimfire semiautomatic pistols that are not already listed on the roster pursuant to Section 32015, it does not have a magazine disconnect mechanism, if it has a detachable magazine.
(7) (A) Commencing January 1, 2010, for all semiautomatic pistols that are not already listed on the roster pursuant to Section 32015, it is not designed and equipped with a microscopic array of characters that identify the make, model, and serial number of the pistol, etched or otherwise imprinted in two or more places on the interior surface or internal working parts of the pistol, and that are transferred by imprinting on each cartridge case when the firearm is fired, provided that the Department of Justice certifies that the technology used to create the imprint is available to more than one manufacturer unencumbered by any patent restrictions.
(B) The Attorney General may also approve a method of equal or greater reliability and effectiveness in identifying the specific serial number of a firearm from spent cartridge casings discharged by that firearm than that which is set forth in this paragraph, to be thereafter required as otherwise set forth by this paragraph where the Attorney General certifies that this new method is also unencumbered by any patent restrictions. Approval by the Attorney General shall include notice of that fact via regulations adopted by the Attorney General for purposes of implementing that method for purposes of this paragraph.
(C) The microscopic array of characters required by this section shall not be considered the name of the maker, model, manufacturer's number, or other mark of identification, including any distinguishing number or mark assigned by the Department of Justice, within the meaning of Sections 23900 and 23920.
